kanes n12 exa update 15/1/2017

Post by **15exa** » Sat Jun 18, 2011 10:36 am

removed inner valve springs last night.

when i put the 10mm fuel feed line in, will i be able to keep 8mm return, or should i go 10mm return also?

Post by **tassuperkart** » Sat Jun 18, 2011 11:25 am

Use whatever you like M8.
Some/any restriction on the return side will do no harm.
L8r
Oracle

Valentich · Post by **Valentich** » Sat Jun 18, 2011 1:45 pm

I did a lot of research when I did mine, and found that at (especially at E15T) power levels, its good to have the return smaller.

It sounds good to have 10mm all the way around, but defiantly not needed

Post by **15exa** » Sat Jun 18, 2011 3:08 pm

kewl, thanks guys

Post by **The Renegade** » Sun Jun 19, 2011 9:03 pm

tassuperkart wrote:......
L8r
Oracle

FKN LOL

Post by **15exa** » Wed Aug 03, 2011 9:33 pm

bit over due for an update.

engine back in.
just waiting on some coin for a few more fittings to finish off fuel system.
mate lent me his mig, so did a bit of repair work, holes in roof from basket, holes in door jam from visor, rust in bottom sill and under quarter windows.
interior floor finished.
dash out and wiring everywhere (again).
lokka back in.
paint started tonight.

try and get a few piccys up tomz

Post by **15exa** » Thu Aug 11, 2011 9:12 pm

ok so i was going to wait till it was done before putting pix up, was bored so, what the heck...... a few to keep yous keen

the upsized 10mm fuel feed line

from back to front

surge tank and new pump

floor done

wiring loom tidied............ again

the aircraft i based my concept on

concept sketch i drew up

just needs the rivits and sheet metal joins airbrushed on, and the bonnet meural painted on and she will be finished

the bombers had thier air craft number on the tail, thought this was fitting

new cooler brackets welded in, cbf cleaning em right up, this will do

zoomzoom · Post by **zoomzoom** » Thu Aug 11, 2011 9:51 pm

looking good mate

Zoomzoom

TurboZ.Dude · Post by **TurboZ.Dude** » Fri Aug 12, 2011 6:35 am

Wow!

Looks awesome!

Nice sketching BTW, you're a pro!

Callumgw · Post by **Callumgw** » Fri Aug 12, 2011 6:56 am

dexi_styles · Post by **dexi_styles** » Fri Aug 12, 2011 8:12 am

Nice looking concept

My misses says "son of a bitch!, now I know who flogged my plates"

I hope she don't find you.... Hahahaha

Dexi

Valentich · Post by **Valentich** » Fri Aug 12, 2011 3:08 pm

Great work as usual, but I'm missing the RAT LOL

Anyway, nice concept, are you going to paint on the rivets or you looking at something else "trick" for that.

Post by **15exa** » Fri Aug 12, 2011 4:43 pm

Valentich wrote:Great work as usual, but I'm missing the RAT LOL

Anyway, nice concept, are you going to paint on the rivets or you looking at something else "trick" for that.

not half as much as i do mate....

yeah i will be airbrushing the rivits and sheet metal joins.

Post by **15exa** » Fri Aug 12, 2011 4:49 pm

TurboZ.Dude wrote:Wow!

Looks awesome!

Nice sketching BTW, you're a pro!

cheers, that was just a half hour job

this is what i can do with a few more hours

RIP EAZY E · Post by **RIP EAZY E** » Fri Aug 12, 2011 5:25 pm

Looks cool.