N12Turbo.com lanyards are now available! Click here to visit the shop
Other then A Catch Can
Other then A Catch Can
Hey guys.
Ok I have the oil over flow on the left side of rocker cover and it used to go to an oil catch can, but I not want one.
So question is where can I run this too??
Is there some where to tap into?? Maybe factory setup??
Thanks
Steve
Ok I have the oil over flow on the left side of rocker cover and it used to go to an oil catch can, but I not want one.
So question is where can I run this too??
Is there some where to tap into?? Maybe factory setup??
Thanks
Steve
- dexi_styles
- Posts: 1227
- Joined: Fri Aug 25, 2006 1:49 pm
- Location: South Brisbane
I have mine running into the intake, under where the otherside going to. I have the pic for you
Dex
Dex
http://forum.n12turbo.com/viewtopic.php?t=446 Benny's Old Dog....
Bringing New life to the Young Dog...
http://forum.n12turbo.com/viewtopic.php?t=348
Bringing New life to the Young Dog...
http://forum.n12turbo.com/viewtopic.php?t=348
UMM dex do you have a one way valve on the left (larger) pipe?????
If you dont you will be just blowing boost into the rocker cover!
that pipe is supposed to be on the turbo intake side so it is only ever vaccuum and the right pipe on the rocker cover has a one way valve between that and the intake.
If you dont you will be just blowing boost into the rocker cover!
that pipe is supposed to be on the turbo intake side so it is only ever vaccuum and the right pipe on the rocker cover has a one way valve between that and the intake.
162.4kw - 588.8nm
http://www.cmsperformance.net/
http://www.cmsperformance.net/
Hm I thought that breather was meant to be pre-turbo not post.
Low Slow and Sarcastic
Always Oscar Mike on the AO
www.twitter.com/garagepanda for my latest Inane comments
www.TasSportImages.com
Always Oscar Mike on the AO
www.twitter.com/garagepanda for my latest Inane comments
www.TasSportImages.com
if you dont want to use a catch can, hook it up the turbo intake, as in between the turbo and the AFM, NOT in front of the AFM.
This is where it is standard..
This is where it is standard..
162.4kw - 588.8nm
http://www.cmsperformance.net/
http://www.cmsperformance.net/
kk
i would think catch cans are only illegal if you have them venting to atmosphere and not back into the intake.
because you dont want to keep the can you will be passing the oil back into the intake and through the afm which i would think will cause problems.
i recommend keeping the catch can and routing the 2 hoses from the rocker into the can with a 3rd running anywhere back to the intake pipes (pre turbo), and filling your catch can with steel wool so the oil wont actually get sucked out just the fumes.
because you dont want to keep the can you will be passing the oil back into the intake and through the afm which i would think will cause problems.
i recommend keeping the catch can and routing the 2 hoses from the rocker into the can with a 3rd running anywhere back to the intake pipes (pre turbo), and filling your catch can with steel wool so the oil wont actually get sucked out just the fumes.
do you have an intake pipe between the turbo and POD? plum it in there...
Members Ride: http://forum.n12turbo.com/viewtopic.php?t=6786
85 ET, M/tech LT10X, T28, FMIC 2.5" Stainless Piping, 3" Intake, Dump n Zorst, JDM Inlet, CA18DET Injectors, Bosch 040, Bodykit, 17s
85 ET, M/tech LT10X, T28, FMIC 2.5" Stainless Piping, 3" Intake, Dump n Zorst, JDM Inlet, CA18DET Injectors, Bosch 040, Bodykit, 17s
Just put a breather on it
My old exa I created from granny spec to a neat little BRIGHT car: http://forum.n12turbo.com/viewtopic.php?t=3903
Current Car: 2004 Vz SS Ute
Current Car: 2004 Vz SS Ute
et king.
Yes I am getting a new one made up as I have now made a air box (its black in the picture) so I can get it regoed.
Just have to think about where to run it as I am doing my best to keep engine bay as tidy as possible.
Thanks Guys for ALL the answers.
Anymore comments?
BAZ, would your idea be legal?
Yes I am getting a new one made up as I have now made a air box (its black in the picture) so I can get it regoed.
Just have to think about where to run it as I am doing my best to keep engine bay as tidy as possible.
Thanks Guys for ALL the answers.
Anymore comments?
BAZ, would your idea be legal?