Posted: Tue Dec 23, 2008 5:51 pm
"The Snow Plough" or "The Cow Catcher" bwaaahahahahaha!
Damn tho.... lookit the freakin shine on that thing........
L8tr
E
Damn tho.... lookit the freakin shine on that thing........
L8tr
E
N12 Turbo Forums
New Track time list section!
https://forum.n12turbo.com/
my project exa 50 grand and 3 years later and still more mod
Page 5 of 5
Posted: Wed Dec 24, 2008 12:42 am
needs deep-dish 3-piece rims now
Posted: Wed Dec 24, 2008 10:10 am
holy crap u filled in all the holes below the windscreen too! LOL
u missed the windscreen washer holes tho!
100% insane bro
u missed the windscreen washer holes tho!
100% insane bro
Posted: Wed Dec 24, 2008 4:24 pm
gotta keep it legal lolAndroid 360 wrote: u missed the windscreen washer holes tho!
In more detail.
Posted: Sun Dec 28, 2008 5:54 pm
Basically we purchased the old girl about 7 to 8 years ago in stock condition, one owner, older lady...bad paint, and few dings...basically the intention was to build a fast n12. Ran it for a few years and made a few mild upgrades as we needed it...ie replacing stock turbo(leaking) with slightly bigger turbo etc... Eventually we got to a point where we had too many electrical and mechanical problems to keep the motor in the car nemore...at this point we got stupid!
Basically the work we got done were done by Mark Ashford, the old owners of Exotic Exhaust, (cant remember gearbox builders name, mark's guy), and ourselves.
Run down of the car.
Motor:
Forged rods and pistons, Nitrided crank, heavely ported Jap head, o/s custom made valves, cam by Sure Cam to suit porting and valves, adjustable cam gear, valve spring upgrade, rocker arms of head balanced, kometic head gasket, o/s gaskets to suit porting, motor balanced.
Airflow:
3inch exhaust, custom exhaust manifold, t3 Turbonetics turbo, Turbonetics external gate, custom engineered inlet manifold(needs to be improved), au falcon throttle body, FMIC
Fuel:
680cc fuel injector, Turbosmart fuel reg, Turbosmart type 3 bov, custom fuel rail, twin msd fuel pump, surge tank
Electrical:
Haltech e6x, 4 x LS1 Commodore Coil Packs, Gizzmo shift light, 10mm Leads, Autometer: oil/p, oil/t, water/t, boost, af, fuel/p
Drive Train:
n13 front hubs, n15ss pulsar brakes, n15ss pulsar rims, Azenis semi slicks, custom combined driveshafts(still all forged bits like nissan end to suit hub difference), n12 belhousing with n13 internals, locked diff, NPC custom clutch to suit intended power, custom flywheel, n13 koni adjustables, coil over springs on front, rear on kings high tension springs.
Interior:
Stripped, no a/con, no fans, no heater condensor, no deading, brand new carpet, custom made dash to suit gauges(see pic), OBX race seat, no rear seats.
Exterior:
Custom made body kit(not the most beautiful...but we needed something to cover the wheels sticking out and it was available to buy), Engine vents molded over, no lines down body, custom fibreglass rear bar(standard but smooth), black paint.
I can't think of much more...alot has been done, still a little to be done...car will be back in brisbane soon, from there we need to get a full power tune, intercooler needs to be modified, few thing here and there in the bay, front seats to be fitted, rear springs needed to be re heated and shrunk, new rims.
We have taken our time...and no intention of starting to hurry now, the car will be hopefully ready by march...just a little to do now...and a not much to pay for...lol! Not sure what she is actually going to perform like, may just break drive shafts and gearboxes all the time. Intentions are to have it running by march and we'll see what it does. Intally on the run-in tune we had a turbo fault, but we had enough go time to get it goin on the dyno, with around 10psi we made almost 200hp atw...then we ran out of boost as the turbo gave up The external gate spring is set at 15psi...
Anyways...i'll try keep u posted...hope u enjoy the pics!
Basically the work we got done were done by Mark Ashford, the old owners of Exotic Exhaust, (cant remember gearbox builders name, mark's guy), and ourselves.
Run down of the car.
Motor:
Forged rods and pistons, Nitrided crank, heavely ported Jap head, o/s custom made valves, cam by Sure Cam to suit porting and valves, adjustable cam gear, valve spring upgrade, rocker arms of head balanced, kometic head gasket, o/s gaskets to suit porting, motor balanced.
Airflow:
3inch exhaust, custom exhaust manifold, t3 Turbonetics turbo, Turbonetics external gate, custom engineered inlet manifold(needs to be improved), au falcon throttle body, FMIC
Fuel:
680cc fuel injector, Turbosmart fuel reg, Turbosmart type 3 bov, custom fuel rail, twin msd fuel pump, surge tank
Electrical:
Haltech e6x, 4 x LS1 Commodore Coil Packs, Gizzmo shift light, 10mm Leads, Autometer: oil/p, oil/t, water/t, boost, af, fuel/p
Drive Train:
n13 front hubs, n15ss pulsar brakes, n15ss pulsar rims, Azenis semi slicks, custom combined driveshafts(still all forged bits like nissan end to suit hub difference), n12 belhousing with n13 internals, locked diff, NPC custom clutch to suit intended power, custom flywheel, n13 koni adjustables, coil over springs on front, rear on kings high tension springs.
Interior:
Stripped, no a/con, no fans, no heater condensor, no deading, brand new carpet, custom made dash to suit gauges(see pic), OBX race seat, no rear seats.
Exterior:
Custom made body kit(not the most beautiful...but we needed something to cover the wheels sticking out and it was available to buy), Engine vents molded over, no lines down body, custom fibreglass rear bar(standard but smooth), black paint.
I can't think of much more...alot has been done, still a little to be done...car will be back in brisbane soon, from there we need to get a full power tune, intercooler needs to be modified, few thing here and there in the bay, front seats to be fitted, rear springs needed to be re heated and shrunk, new rims.
We have taken our time...and no intention of starting to hurry now, the car will be hopefully ready by march...just a little to do now...and a not much to pay for...lol! Not sure what she is actually going to perform like, may just break drive shafts and gearboxes all the time. Intentions are to have it running by march and we'll see what it does. Intally on the run-in tune we had a turbo fault, but we had enough go time to get it goin on the dyno, with around 10psi we made almost 200hp atw...then we ran out of boost as the turbo gave up The external gate spring is set at 15psi...
Anyways...i'll try keep u posted...hope u enjoy the pics!
Posted: Sun Dec 28, 2008 5:56 pm
Posted: Sun Dec 28, 2008 5:58 pm
Posted: Sun Dec 28, 2008 6:04 pm
Oh wow! Nice job with the dash! That's some professional quality there m8!
Posted: Sun Dec 28, 2008 6:29 pm
You've certainly done a lot of good work!, keep it up!
C
C
Posted: Thu Oct 15, 2009 3:30 am
hello mate
very nice car ..crazy mod's keep it up ....i will like soon to see a dyno from this monster!!
cheers
george
very nice car ..crazy mod's keep it up ....i will like soon to see a dyno from this monster!!
cheers
george
Posted: Wed Apr 21, 2010 11:04 pm
any updates?
Posted: Thu Apr 22, 2010 3:33 am
^^^ what he said.