General chat related to anything N12.
photoglossy
Posts: 2135 Joined: Wed Aug 02, 2006 10:23 pm
Location: Auckland, NZ
Contact:
Post
by photoglossy » Thu Aug 07, 2008 11:27 am
Hey guys. Is anyone here running these injectors? Look to be suitable but just thought id ask before i buy them... ($70) 444cc so should gimme a lil extra go
Cheers
photoglossy
photoglossy
Posts: 2135 Joined: Wed Aug 02, 2006 10:23 pm
Location: Auckland, NZ
Contact:
Post
by photoglossy » Thu Aug 07, 2008 11:33 am
Grrrrr SR injectors dont bolt in do they... scrap that!
photoglossy
BennyET
Posts: 1372 Joined: Thu Aug 03, 2006 7:51 am
Location: Gold Coast, Qld
Post
by BennyET » Thu Aug 07, 2008 1:27 pm
sr are side feed injectors which are not a bolt on. those pictured arent side feed. at 444cc they are probably gtr squirters
$70 is a bargain!
I understand the need for conformity. Without a concise set of rules to follow we would probably all have to resort to common sense.
BennyET
Panda_ET
Posts: 3835 Joined: Wed Aug 02, 2006 10:02 pm
Location: Launceston
Contact:
Post
by Panda_ET » Thu Aug 07, 2008 6:07 pm
no no guys from what i can remember the GTiR DOESNT use side feed injectors they are different to the normal srs !! they are top feed like ours. I remember something about that when i was looking for upgrades
Panda_ET
photoglossy
Posts: 2135 Joined: Wed Aug 02, 2006 10:23 pm
Location: Auckland, NZ
Contact:
Post
by photoglossy » Thu Aug 07, 2008 6:09 pm
Ok, well ill see how the auction goes
Ill get them cleaned when i buy them too. 444's should go just fine in the lil E15
photoglossy
15exa
Administrator
Posts: 1015 Joined: Mon Aug 07, 2006 11:00 am
Location: brisbane
Post
by 15exa » Thu Aug 07, 2008 6:25 pm
yeah they are gtr injectors
nice score for $70
15exa
photoglossy
Posts: 2135 Joined: Wed Aug 02, 2006 10:23 pm
Location: Auckland, NZ
Contact:
Post
by photoglossy » Thu Aug 07, 2008 8:31 pm
Bidding will probably go over $100 but thats still good i guess
photoglossy
15exa
Administrator
Posts: 1015 Joined: Mon Aug 07, 2006 11:00 am
Location: brisbane
Post
by 15exa » Thu Aug 07, 2008 8:58 pm
dont be supprised if they go for over $200
i picked up a set of 6 for $170 from japan a few months back
good luck with the bidding
15exa
tassuperkart
Administrator
Posts: 5578 Joined: Wed Jul 05, 2006 8:39 pm
Location: Southern Tasmania
Contact:
Post
by tassuperkart » Thu Aug 07, 2008 9:41 pm
You wont get any extra "go" with them.
They will do NOTHING apart from make it more difficult to tune unless you are actually maxing the original injectors.
Are you?
440 cc injectors are almost too big for ANY et.
If not then spend you money to actually make a difference elsewhere until you actually DO max the stockers out.
L8tr
E
Forcd4 wrote: Oh fuk no dude it's you a again, the oracle.
tassuperkart
photoglossy
Posts: 2135 Joined: Wed Aug 02, 2006 10:23 pm
Location: Auckland, NZ
Contact:
Post
by photoglossy » Fri Aug 08, 2008 4:30 am
Will be getting close to maxing them out when its all done.
Im getting the ecu chipped and tuned and the dude can do it to suit any AFM and set of injectors, so i thought i may as well tune it to something thats a bit bigger than standard... just incase i do even more to it in the future.
photoglossy
tassuperkart
Administrator
Posts: 5578 Joined: Wed Jul 05, 2006 8:39 pm
Location: Southern Tasmania
Contact:
Post
by tassuperkart » Fri Aug 08, 2008 7:35 pm
440's are not a "bit" bigger M8
They are frikken huge.
Nup, I doubt you'll go close to maxing them. Not with a stock (albeit chipped) setup.
However, its your money and spend it as you wish.
L8tr
E
Forcd4 wrote: Oh fuk no dude it's you a again, the oracle.
tassuperkart
shanec86
Administrator
Posts: 1454 Joined: Mon Jul 03, 2006 8:00 pm
Location: Melbourne
Contact:
Post
by shanec86 » Fri Aug 08, 2008 8:11 pm
440 arent big, dont be scared. They arent going to be that much harder to tune...
we run Sard 700cc injectors in my brothers Rb25 and it was no harder to tune than any other car that we've had. Idles perfect and uses just as much fuel putting round as it does my pulsar on standard injectors. made 277rwkw on 1.1bar ^_^
shanec86
photoglossy
Posts: 2135 Joined: Wed Aug 02, 2006 10:23 pm
Location: Auckland, NZ
Contact:
Post
by photoglossy » Sat Aug 09, 2008 6:05 am
Cheers shane. Imma get them and see how they go.
Any know of i need to screw around with resistors and stuff??? Thats a part of my brain that was lacking at birth unfortunately...
photoglossy
photoglossy
Posts: 2135 Joined: Wed Aug 02, 2006 10:23 pm
Location: Auckland, NZ
Contact:
Post
by photoglossy » Sat Aug 09, 2008 5:13 pm
Auction went over $130 so i pulled out... possibly got some others lined up tho.
photoglossy
15exa
Administrator
Posts: 1015 Joined: Mon Aug 07, 2006 11:00 am
Location: brisbane
Post
by 15exa » Sat Aug 09, 2008 6:15 pm
15exa wrote: dont be supprised if they go for over $200
i picked up a set of 6 for $170 from japan a few months back
good luck with the bidding
not gona say o told ya so
15exa