N12 Turbo Forums

... by myself and my cousin Johny at PERFORMANCE PIPES in Brisbane ... microtech... custom everything to much to list.... surely someone knows of ... have parts off her for sure if it has been wrecked... spare gearbox’s , cylinder heads, turbos, I had everything twice and it all went with it!!,,,, ...

OK, Your right, microtech do not support the MT series ECU's anymore ... to work on the ET. if its off anything other than a 4 cyl Nissan then leave it alone as you will have to ... concerned, they might just load a generic turbo 4 cylinder tune. You may find this artical of use. http://forum.n12turbo.com/viewtopic.php?t=2340 ...

... had already popped the injector outputs and Microtech DIDNT test it at all Just run them back ... remeber the correct wiring sequence tho for a 4 cylinder. in the meantime, just wire them back in SERIES ...

... Im suspecting there is more at play in my setup that meets the eye. The Microtech originally came off my FJ20 and ran as sweet as you like. Pretty ... sequential. So Im actually seeing a doubling of the latency time per cylinder firing event which is increasing the effects of latency by double. ...

... the bastards taped together), isolate the fuel pump so you can run the Microtech test (firing plugs and injectors @ 1800rpm, set the cylinder # to zero), watch for the light show. Failing that, swap over to Dexi's distributor, ...

... up everything underneath. I gave myself about 4 hours to do the entire fitup. However, things ... have a look at the CAS indicator on the Microtech and Im getting no CAS signal.......ehh???.............Ahhhhhh!! ... when you get that!!! However, it was down a cylinder.. this was strange as I had ...

... for the new application. You cannot take your Microtech with you unless its another 4 cylinder Nissan with the same config or ignition and Mictrotech WILL ...

... then another, we thought we'd better stop while I still had one working cylinder. Sent the x4 off to Microtech where they replaced 3 blown drivers and tracks (their terminology), damage $100. ...

Are you running a single coil with the Microtech or a x4. Having exactly the same symptoms without the compression ... the good ones and blew another 2. I now have one firing cylinder but at least we know it's the shit Microtech. Am ...

... noticed splattering it sounds like a wrx, then got home and noticed one cylinder isnt firing, its got spark and i changed the plug but still the same. Its running microtech and i also checked radiator and dipstick all looks fine any ideas?

... this instability due to electrical noise issue in its release notes. Microtech does not have any issue at all in reading the 2 degree slots for ... and just use the leading edge of the smaller slot to trigger the next cylinder in a pre-set sequence. When the long slot comes around the entire ...

... the ECU into diagnostic mode by selecting zero cylinders in the Number of cylinders setup screens ... and that they agree with the settings on a Microtech wiring diagramme for Nissan 4 cylinder? If still no go then its fair to assume the ECU ...

... slot count down to a more manageable number. Microtech has a simple digital offset adjustment ... to fit to Nissan Cas's. This will bring the 4 crank triggering slots back to read at around ... trigger. The ECU then knows exactly when # 1 cylinder is ready to fire and can then sequence ...

... 1986 Colour: Gray/ black Period of ownership: Bought it 2009-11-23 ECU: Microtech Lt10s + x4 ignition, handcontroller, 60-2 trigger wheel, vr-sensor. Rebuild engine: Ross forged pistons, shot peened rods, polished crank, cylinder head rebuild - port and valve job, Camtech camshaft 285/ 288, Camtech ...

... absolutely CERTAIN that each injector driver is going to the correct cylinder number. This "can" cause weird slow running and starting ... pay dearly. Your using an aftermarket ECU right? I seem to recall a Microtech? If so piss off the stock resistor block (if its still there). ...