N12Turbo.com lanyards are now available! Click here to visit the shop
Has anyone got a match
Help Help and more help....
OK I was thinking this will be it...
Get if finished at any cost...
So today, the first time I touched it in months...
Another F@#KING problem....
OK.... she Idles fine...
But in gear... under load... there is nothing....
no power, splattering. struggling and dies
I know this is a problem I have read about...
but i cant remember where and what is the fix.
I plugged and unplugged the ECU a few times, Played with timing....
Anyway... While I am looking through post...
Any suggestions...... Please
OK I was thinking this will be it...
Get if finished at any cost...
So today, the first time I touched it in months...
Another F@#KING problem....
OK.... she Idles fine...
But in gear... under load... there is nothing....
no power, splattering. struggling and dies
I know this is a problem I have read about...
but i cant remember where and what is the fix.
I plugged and unplugged the ECU a few times, Played with timing....
Anyway... While I am looking through post...
Any suggestions...... Please
Last edited by Valentich on Sat Apr 13, 2013 2:59 pm, edited 1 time in total.
why do you keep writing in bigger letters & in colours :\
My old exa I created from granny spec to a neat little BRIGHT car: http://forum.n12turbo.com/viewtopic.php?t=3903
Current Car: 2004 Vz SS Ute
Current Car: 2004 Vz SS Ute
Air leak post AFM pre manifold. Check your hose clamps and the harness to the AFM.
Damo
Damo
Do humanity a favor, use your brain and fight the forces of WOO WOO!
http://www.youtube.com/watch?v=G1mrbxhWU5Y
http://www.youtube.com/watch?v=G1mrbxhWU5Y
Hey,
I Had a quick look but could not find any air leaks...
I did find something strange.
if I unplug lead 1 or 4 there is a drop in idle
if I unplug lead 2 or 3 there is no change,
In fact, if i set the lead on the plug, but not all the way one, then it idles faster
I tried moving it like this and it felt like it had more power, not normal but much better.
I dont know anything about the CAS.
But I hear that strange things happens when they play up.
I'm going to give it another go tomorrow,
If anyone wants to make a quick $100 or so, I could do with the help LOL
I Had a quick look but could not find any air leaks...
I did find something strange.
if I unplug lead 1 or 4 there is a drop in idle
if I unplug lead 2 or 3 there is no change,
In fact, if i set the lead on the plug, but not all the way one, then it idles faster
I tried moving it like this and it felt like it had more power, not normal but much better.
I dont know anything about the CAS.
But I hear that strange things happens when they play up.
I'm going to give it another go tomorrow,
If anyone wants to make a quick $100 or so, I could do with the help LOL
Thanks guys.....
And thanks robbo
once more unto the breach......
I have taken it to a local mechanic...
where I can keep it for a why and work on it.
First is the brakes
$450 for a new master cylinder....
I could of got the old one redid... but a little bit more and its new...
? As I put discs on the back... what effect should i expect.... re: stopping.
I have not thought about the proportioning valve yet.. and am hopping I can live with it for now ?
And thanks robbo
once more unto the breach......
I have taken it to a local mechanic...
where I can keep it for a why and work on it.
First is the brakes
$450 for a new master cylinder....
I could of got the old one redid... but a little bit more and its new...
? As I put discs on the back... what effect should i expect.... re: stopping.
I have not thought about the proportioning valve yet.. and am hopping I can live with it for now ?
your weight distribution is different to EXA and ET, so it's not possible to say. What you need to do it find a bit of closed road (so its safe) and do a brake test - Stop hard and see when the rear locks before the front. Ideally the front should always lock first when braking hard in a straight line. Also this should ideally be done in the 'worst case configuration' which would be wet road with least weight in back. Don't do it from stupid fast speeds, it wont have too much bearing on the outcome, they'll lock from 60 with a hard stop as easy as from 100. Depending on the rest decide what to do next.
Legally you need an engineer to sign off on the change you've made.
C
Legally you need an engineer to sign off on the change you've made.
C
Thanks...
I did try swopping them over in a desperate attempt to get it running but it made no real difference.
But its been a good day.
Got the Prairie on the hoist, so I could weld the bracket for the hand brake.
So I have a working hand brake for the first time in 6 months,
I cant tell you how much of a pain it was not having one.
Got the new MC in
This by itself has been the most expensive part of the build, this baby cost me $500,
and as I was quoted $350 for a reco (apparently this is some sort of none standard one)
I thought..... Screw it...... for $150 more get the new original Nissan one.
and It was the only one the parts people could find.... and it came from Tamworth over night.
And in less than an hour it was in and the brake bleed right through...
Damn a hoist makes things so easy...
So I have brakes again.......
Next.... Monday... Getting the thing running right
We had a quick look using the timing gun and could see it was out.... But thats for Monday
I did try swopping them over in a desperate attempt to get it running but it made no real difference.
But its been a good day.
Got the Prairie on the hoist, so I could weld the bracket for the hand brake.
So I have a working hand brake for the first time in 6 months,
I cant tell you how much of a pain it was not having one.
Got the new MC in
This by itself has been the most expensive part of the build, this baby cost me $500,
and as I was quoted $350 for a reco (apparently this is some sort of none standard one)
I thought..... Screw it...... for $150 more get the new original Nissan one.
and It was the only one the parts people could find.... and it came from Tamworth over night.
And in less than an hour it was in and the brake bleed right through...
Damn a hoist makes things so easy...
So I have brakes again.......
Next.... Monday... Getting the thing running right
We had a quick look using the timing gun and could see it was out.... But thats for Monday
Doesn't really make it easier to read at all, its actually more annoying to be honest, its the main reason why i haven't followed this thread, fuck reading this colored writing bullshit lol
My old exa I created from granny spec to a neat little BRIGHT car: http://forum.n12turbo.com/viewtopic.php?t=3903
Current Car: 2004 Vz SS Ute
Current Car: 2004 Vz SS Ute