thought some of you might be interested in the other toys i play with.
First one is a 89' G50 Infiniti Q45, JDM, VH45 and on bags. Work Euroline 17x9 -0 & 18x9 +6. Engine has been completely rebuilt, ECU, blitz filter. This is the VIP mobile with lots of options and things to playwith inside
N12Turbo.com lanyards are now available! Click here to visit the shop
Shane's other toys
Shane's other toys
Last edited by shanec86 on Sun May 30, 2010 10:32 pm, edited 1 time in total.
162.4kw - 588.8nm
http://www.cmsperformance.net/
http://www.cmsperformance.net/
Next is my r31 track car
currently putting the new turbo and plenum on + lots of other bits and pieces.
Engine
Block-
Decked
Bored 20thou
Honed
Acid Washed
Brass Welsh Plugs
Every thread re-tapped
new water line fittings
Head-
Wade cam profile# 1528
HD Valve Springs
Machined Lifter Housing
New Hydraulic Lifters
Port and Polish
Shaved Head
Pressure Test etc.
New Exhaust Studs
Internals-
Polished Crank Journals
Resized Rods
ACL 20thou Duralite Pistons - Custom made, 8.5:1 compression
HPC coated piston crowns
HPC coated valves
ARP Head STUD kit
ARP Rod bolts
ARP Flywheel bolts
ACL 1.3mm Multi-layer Stainless Head Gasket
Totally balanced - clutch/flywheel/crank/balancer.. the lot
Other bits-
ACL Race series Gasket Set
ACL Race series Bearings
Ported/Matched JD custom plenum/runners
Ported/Polished XF Throttle Body
Linished manifolds
Bead Blasted all engine parts
New VL Turbo Oil Pump
New Water pump
New timing belt kit
New crank gear
New keyway's
Bosch 363 Injectors on custom fuel rail
Garrett 35/40 .86 rear
Stainless Steel High mount manifold
Turbo Blanket
Turbosmart 48mm Pro gate with screamer
4" inlet with huge pod filter
3" dump pipe back exhaust, straight through to 3" muffler
Wolf 3d v4 ecu
EL falcon multicoils
Custom engine loom with brand new plugs
EA falcon inlet temp sensor
Engine oil cooler
Suspension / Brakes:
R32 GTR Slotted/Drilled Front rotors
R33 GTST 4 piston Front Calipers
R32 GTS Slotted/Drilled Rear Rotors
R33 GTST 2 Piston Rear Calipers
Hyrdaulic Handbrake
S13 Front Hubs / Knuckles
R31 Lower control arms with new Ball joints
R31 Tie rods/ends
ISC S13 Coilovers 12/8kg
Whiteline front Strut brace
Rear lower control arms boxed
Nolathane control arm bushes
Custom master cylinder brace
Whiteline adjustable panhard rod
Wheels / Driveline:
Front - 27mm spacers
17x9" Drifteks
Drift - 235/45/17
Circuit - 250/620/17 Avon full slicks
or
f. 225/45/17 Bridgestone semis
r. 275/40/17 Toyo r888 semis
Rear - 27mm spacers
17x9" Sparco
17x7" Sensei
16x8" Enkei
15x6.5" Black racing
15x6 TI rims
15x6 Silo rims
Auto 3.9 ratio Diff
Minispool
R33 RB25DET 5spd Manual gearbox
R31 Pintara Gearshifter
R31 Pintara clutch master cylinder / slave cylinder
Excedy 5 Puck clutch / pressure plate - custom built
Tailshaft loop
Interior / Exterior
TI Bonnet / Grill
Series 3 bar with MFX Lip
Stickers
Tinted indicators, taillights, headlights, everything
Painted garnish and door frames black
Fibreglass bonnet vent
Sparco Bonnet pins
removed passenger mirror
removed rear wing
Bride style Justjap seat
Sabelt 100mm 4 point camlock harness
Gktech deep dish steering wheel
Speco water temp guage
OBX oil temperature guage
Autometer boost guage
Autometer oil pressure guage
Autometer monster tacho
removed sound deadening
aluminium door panels
drivers door manual window reg
ecu, ignitors, relays mounted where glove box was
fire extinguisher
Custom loom, minimum wires left
Stripped interior
Battery relocated to passenger side rear foot well with breather
250amp circuit breaker
Bond 6 point boltin roll cage with intrusion bar
currently putting the new turbo and plenum on + lots of other bits and pieces.
Engine
Block-
Decked
Bored 20thou
Honed
Acid Washed
Brass Welsh Plugs
Every thread re-tapped
new water line fittings
Head-
Wade cam profile# 1528
HD Valve Springs
Machined Lifter Housing
New Hydraulic Lifters
Port and Polish
Shaved Head
Pressure Test etc.
New Exhaust Studs
Internals-
Polished Crank Journals
Resized Rods
ACL 20thou Duralite Pistons - Custom made, 8.5:1 compression
HPC coated piston crowns
HPC coated valves
ARP Head STUD kit
ARP Rod bolts
ARP Flywheel bolts
ACL 1.3mm Multi-layer Stainless Head Gasket
Totally balanced - clutch/flywheel/crank/balancer.. the lot
Other bits-
ACL Race series Gasket Set
ACL Race series Bearings
Ported/Matched JD custom plenum/runners
Ported/Polished XF Throttle Body
Linished manifolds
Bead Blasted all engine parts
New VL Turbo Oil Pump
New Water pump
New timing belt kit
New crank gear
New keyway's
Bosch 363 Injectors on custom fuel rail
Garrett 35/40 .86 rear
Stainless Steel High mount manifold
Turbo Blanket
Turbosmart 48mm Pro gate with screamer
4" inlet with huge pod filter
3" dump pipe back exhaust, straight through to 3" muffler
Wolf 3d v4 ecu
EL falcon multicoils
Custom engine loom with brand new plugs
EA falcon inlet temp sensor
Engine oil cooler
Suspension / Brakes:
R32 GTR Slotted/Drilled Front rotors
R33 GTST 4 piston Front Calipers
R32 GTS Slotted/Drilled Rear Rotors
R33 GTST 2 Piston Rear Calipers
Hyrdaulic Handbrake
S13 Front Hubs / Knuckles
R31 Lower control arms with new Ball joints
R31 Tie rods/ends
ISC S13 Coilovers 12/8kg
Whiteline front Strut brace
Rear lower control arms boxed
Nolathane control arm bushes
Custom master cylinder brace
Whiteline adjustable panhard rod
Wheels / Driveline:
Front - 27mm spacers
17x9" Drifteks
Drift - 235/45/17
Circuit - 250/620/17 Avon full slicks
or
f. 225/45/17 Bridgestone semis
r. 275/40/17 Toyo r888 semis
Rear - 27mm spacers
17x9" Sparco
17x7" Sensei
16x8" Enkei
15x6.5" Black racing
15x6 TI rims
15x6 Silo rims
Auto 3.9 ratio Diff
Minispool
R33 RB25DET 5spd Manual gearbox
R31 Pintara Gearshifter
R31 Pintara clutch master cylinder / slave cylinder
Excedy 5 Puck clutch / pressure plate - custom built
Tailshaft loop
Interior / Exterior
TI Bonnet / Grill
Series 3 bar with MFX Lip
Stickers
Tinted indicators, taillights, headlights, everything
Painted garnish and door frames black
Fibreglass bonnet vent
Sparco Bonnet pins
removed passenger mirror
removed rear wing
Bride style Justjap seat
Sabelt 100mm 4 point camlock harness
Gktech deep dish steering wheel
Speco water temp guage
OBX oil temperature guage
Autometer boost guage
Autometer oil pressure guage
Autometer monster tacho
removed sound deadening
aluminium door panels
drivers door manual window reg
ecu, ignitors, relays mounted where glove box was
fire extinguisher
Custom loom, minimum wires left
Stripped interior
Battery relocated to passenger side rear foot well with breather
250amp circuit breaker
Bond 6 point boltin roll cage with intrusion bar
162.4kw - 588.8nm
http://www.cmsperformance.net/
http://www.cmsperformance.net/
suprise another skyline. This one is a very long term project
Basically its an 86' HR31 Passage GT with a NICS rb20det as standard.
This is being replaced with a VH41 which is a Quad cam 4.1lt Nissan alloy v8 for those who dont know. It'll be turbo too.
Its getting a complete rebuild from the shell up.
Basically its an 86' HR31 Passage GT with a NICS rb20det as standard.
This is being replaced with a VH41 which is a Quad cam 4.1lt Nissan alloy v8 for those who dont know. It'll be turbo too.
Its getting a complete rebuild from the shell up.
162.4kw - 588.8nm
http://www.cmsperformance.net/
http://www.cmsperformance.net/
Quite a collection you have there ..Love them all tho
My old exa I created from granny spec to a neat little BRIGHT car: http://forum.n12turbo.com/viewtopic.php?t=3903
Current Car: 2004 Vz SS Ute
Current Car: 2004 Vz SS Ute
Very nice!!!
Did you do the plenum yourself? Will be good to see if it lets you rev out a bit better.
Just need a little more of a push to get my 31 underway, and that pic may just be it.
Damo
Did you do the plenum yourself? Will be good to see if it lets you rev out a bit better.
Just need a little more of a push to get my 31 underway, and that pic may just be it.
Damo
Do humanity a favor, use your brain and fight the forces of WOO WOO!
http://www.youtube.com/watch?v=G1mrbxhWU5Y
http://www.youtube.com/watch?v=G1mrbxhWU5Y
haha damo, nah it was a unit that someone else does. Cant remember the name.
haha yes on track with the exa
I do race the 31, havent been out a little while since it had a slight mishap.
Will attempt to get it out a whole lot more when its (re)finished.
haha yes on track with the exa
I do race the 31, havent been out a little while since it had a slight mishap.
Will attempt to get it out a whole lot more when its (re)finished.
162.4kw - 588.8nm
http://www.cmsperformance.net/
http://www.cmsperformance.net/