turbo

General chat related to anything N12.
Post Reply
smurf69
Posts: 40
Joined: Sun Jul 01, 2007 12:15 pm

turbo

Post by smurf69 » Fri Jul 06, 2007 11:50 am

hey peoplz i have a 84 et pulsar when i brought it it wasnt running properly played around wid a few sensors it sorted the problem for about two weeks and plus it had a manifold gasket leak so i pulled the turbo off to find that it is a SCHWITZER turbo does anyone have any information on these turbo's are they a T2 or what need to know can anyone help me!
HIR8TDET

User avatar
Ash
Administrator
Administrator
Posts: 3246
Joined: Thu Aug 03, 2006 7:17 am
Location: Wangaratta, Victoria, Australia

Post by Ash » Fri Jul 06, 2007 12:00 pm

you might want to ask this question in general tech and modifications. the Schwitzer is about a Garrett T25 sized turbo and oil cooled only. i have 1 sitting on my TV cabinet coz it sucks but thats just my opinion. stuff all midrange or top end poke as far as i'm concerned. some people like them though.

i'd say get a Garrett T25, T25G, or T28. you won't go back!

User avatar
shanec86
Administrator
Administrator
Posts: 1454
Joined: Mon Jul 03, 2006 8:00 pm
Location: Melbourne
Contact:

Post by shanec86 » Fri Jul 06, 2007 12:41 pm

I used to run a schwitzer, was the equivilent to a T25 although with a larger exhaust wheel. It had huge midrange power, and pretty decent top end. The only problem i had was the wastegate was too small for my application and would over boost, even with the wastegate fully open. I bored it out and fixed this a little, but still had problems with that. so i changed for a t28bb.

They are very well built turbos, none of that cheaper stuff you should watch out for.

User avatar
etking
Posts: 1199
Joined: Mon Aug 07, 2006 12:42 pm
Location: Hobart, Tas

Post by etking » Fri Jul 06, 2007 2:39 pm

stick with the shwitzer otherwise u will have to make up a new dump pipe as they have a different flange, but are good turbos for the ets
Members Ride: http://forum.n12turbo.com/viewtopic.php?t=6786
85 ET, M/tech LT10X, T28, FMIC 2.5" Stainless Piping, 3" Intake, Dump n Zorst, JDM Inlet, CA18DET Injectors, Bosch 040, Bodykit, 17s

User avatar
Ash
Administrator
Administrator
Posts: 3246
Joined: Thu Aug 03, 2006 7:17 am
Location: Wangaratta, Victoria, Australia

Post by Ash » Fri Jul 06, 2007 2:49 pm

etking wrote:stick with the shwitzer otherwise u will have to make up a new dump pipe as they have a different flange, but are good turbos for the ets
different flange? the Schwitzer i have has the same t25 style turbine inlet flange and dump flange. :?

User avatar
etking
Posts: 1199
Joined: Mon Aug 07, 2006 12:42 pm
Location: Hobart, Tas

Post by etking » Fri Jul 06, 2007 2:54 pm

my mates only had a 4 bolt flange i think .. well i know it was different to the t25 on the dump side
Members Ride: http://forum.n12turbo.com/viewtopic.php?t=6786
85 ET, M/tech LT10X, T28, FMIC 2.5" Stainless Piping, 3" Intake, Dump n Zorst, JDM Inlet, CA18DET Injectors, Bosch 040, Bodykit, 17s

User avatar
Ash
Administrator
Administrator
Posts: 3246
Joined: Thu Aug 03, 2006 7:17 am
Location: Wangaratta, Victoria, Australia

Post by Ash » Fri Jul 06, 2007 3:03 pm

etking wrote:my mates only had a 4 bolt flange i think .. well i know it was different to the t25 on the dump side
ah ok. must be different series Schwitzer's or something. mine is just an oil cooled T25 sized Schwitzer.

the dump flange is the same apart from an extra bolt hole on the Schwitzer.

T25 left, Schwitzer middle and T25G right,
Image

T25 left, Schwitzer middle and T25G right,
Image

User avatar
etking
Posts: 1199
Joined: Mon Aug 07, 2006 12:42 pm
Location: Hobart, Tas

Post by etking » Sat Jul 07, 2007 12:02 pm

yeh it was different to that, think it was bigger, but meh who knows, go the garretts :D he has t26g now
Members Ride: http://forum.n12turbo.com/viewtopic.php?t=6786
85 ET, M/tech LT10X, T28, FMIC 2.5" Stainless Piping, 3" Intake, Dump n Zorst, JDM Inlet, CA18DET Injectors, Bosch 040, Bodykit, 17s

User avatar
Ash
Administrator
Administrator
Posts: 3246
Joined: Thu Aug 03, 2006 7:17 am
Location: Wangaratta, Victoria, Australia

Post by Ash » Sat Jul 07, 2007 8:41 pm

a T26G?

User avatar
Panda_ET
Posts: 3835
Joined: Wed Aug 02, 2006 10:02 pm
Location: Launceston
Contact:

Post by Panda_ET » Sat Jul 07, 2007 8:44 pm

yeh ,man its fully custom T26G yo
Low Slow and Sarcastic
Always Oscar Mike on the AO

www.twitter.com/garagepanda for my latest Inane comments

www.TasSportImages.com

User avatar
Ash
Administrator
Administrator
Posts: 3246
Joined: Thu Aug 03, 2006 7:17 am
Location: Wangaratta, Victoria, Australia

Post by Ash » Sat Jul 07, 2007 8:46 pm

oh. stupid me. i should of known hey! fully CUSTOM! :oops: :D

User avatar
etking
Posts: 1199
Joined: Mon Aug 07, 2006 12:42 pm
Location: Hobart, Tas

Post by etking » Sun Jul 08, 2007 1:09 pm

yeh its o so custom lol typo :P
Members Ride: http://forum.n12turbo.com/viewtopic.php?t=6786
85 ET, M/tech LT10X, T28, FMIC 2.5" Stainless Piping, 3" Intake, Dump n Zorst, JDM Inlet, CA18DET Injectors, Bosch 040, Bodykit, 17s

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests