N12 Turbo Forums

... striker plate- it moves about smoothly. Only issue is that i'm not sure what positions on the striker plate correspond to what gear. The factory manual isnt very clear on that- just shows the shift pattern on the actual stick, via the linkage. The striker goes back and forth nicely- there appears ...

... striker plate- it moves about smoothly. Only issue is that i'm not sure what positions on the striker plate correspond to what gear. The factory manual isnt very clear on that- just shows the shift pattern on the actual stick, via the linkage. The striker goes back and forth nicely- there appears ...

... it out as it didnt look like a good idea to leave it floating around unsecured in there and put the driveshafts back in. (i already counsulted the manual, and the exploded diagram of the transaxle doesn't feature the little ring spring.. so i was pretty stumped on it) Anyone have any idea if it's ...

... removing large nut) and then forward out of the way to remove the shafts. Whithin 5 minutes from here it can be back on the ground. Never had a manual the first time I did this, looks like it saved me some grief

Looking through the manual, the fuel return hose on E15ET is on the fuel pump. Where the N/A is into the tank beside the float unit. I'm going off the pencil drawings in the book.

And I think the hose for the fuel pump on turbo is bigger
Other than that, the tank should be same size

Dexi

electronic or manual?

Post up a link to help out bro

Michael

... high boost/load to allow the ECU to make a meaningful adjustment. I just make a note of whats happening and select the loadpoints by hand and make manual adjustments so no biggie. My lower/mid boost afr's are now sailin g around 12 even and the upper boost still lurking around 10.8 so just a bit ...

... porting on the head. 4-2-1 extractors. 2.5 inch exhaust. Cat and muffler replaced with resonator. Weber 32/36 Carb. Removed A/C system. Stock 5spd manual trans. Interior Mods: Was reupholstered year before I got it. Volt and Oil pres gauge pods added. Exterior Mods: Fresh paint. Sunroof Installed. ...

yeah ill be checking it tonight and let you know its got me stuffed that two gear boxes have done the same thing is there anything in the manual about the electrics in the gear box i thought that there were electrics for shift solarnoids?????????? could that be a problem ?????????

Check it: http://www.ebay.com.au/itm/Nissan-Pulsar-N13-manual-Gearbox-5-Speed-Driveshafts-Non-Lsd-Sss-Drive-Shaft-/110950167086?pt=AU_Car_Parts_Accessories&hash=item19d525322e http://www.ebay.com.au/itm/Ca16DE-5sp-gearbox-suit-Nissan-n13-exa-pulsar-/170907689373?pt=AU_Car_Parts_Accessories&hash=item27cae4619d ...

... help them along a bit. nah- 13mm ring spanner / socket wont fit on them at all- could be the wrong nuts fitted though. It does say in the service manual to chuck them after removing them once- i'm guessing some genius beforehand decided to ignore that. Advice to everyone- spend the money, chuck ...

... in the first place? Wrong grade nuts installed? Reason why i tried removing them was to get the cv's out- followed the full nissan factory service manual instructions. ideas would be appreciated!

... from China! Going to start fitting the kit today or tomorrow, have you got any tips for placement of the actuators? The kit didn't come with any manual but a DIY guy doesn't need a manual. :twisted: I've already tested the kit, it works. I plugged the main power to an ATX power supply and plugged ...

... like they would just bend the lift points to me as there is no little slot in them like the scissor jack has on it. Looked in the full factory manual that arrived last night, and the diagram for where to position the axle stands isn't all that clear.. it's about the size of a 20 cent piece ...

... a microtech and tune but they never reset the lifters after the dyno run so now I gotta do it but have know idea,how to go about it I've got the manual out but it not much help,don't really know how to read it 0.28 for valve clearance cold for both sides,is that rite, if so how do I go about ...