N12Turbo.com lanyards are now available! Click here to visit the shop

Search found 389 matches: flywheel

Searched query: flywheel

by KiloooNL
Mon Mar 11, 2019 11:58 am
Forum: General Tech & Modifications
Topic: Flywheel bolt torque
Replies: 10
Views: 8149

Flywheel bolt torque

... been able to take the bell housing of yet. It seems to be stuck (?) with all the bolts removed. However, my question actually was: can I reuse my flywheel bolts? My Haynes doesn't tell me I have to change those, but normally you have to, right? Hope my flywheel will not look like yours, TurboZ.dude. ...
by MartinodePueblo
Mon Mar 11, 2019 6:04 am
Forum: General Tech & Modifications
Topic: Flywheel bolt torque
Replies: 10
Views: 8149

Flywheel bolt torque

... been able to take the bell housing of yet. It seems to be stuck (?) with all the bolts removed. However, my question actually was: can I reuse my flywheel bolts? My Haynes doesn't tell me I have to change those, but normally you have to, right? Hope my flywheel will not look like yours, TurboZ.dude.
by B11Chris
Sun Feb 24, 2019 5:55 pm
Forum: General Tech & Modifications
Topic: Clutch?
Replies: 6
Views: 4419

Clutch?

... Research shows the stock E15ET clutch disk is 200mm, while the stock disk for a E16 B11 is 180mm, but both have the same part number for the flywheel, so we'll see if it works transmission inpunt shaft spline count and width differs between E15ET and E16, so I'd say no. Maybe its just here ...
by gettu
Sat Feb 23, 2019 5:20 pm
Forum: General Tech & Modifications
Topic: Clutch?
Replies: 6
Views: 4419

Clutch?

B11Chris wrote: Wed Feb 13, 2019 5:11 pm Thats what I just ordered. Research shows the stock E15ET clutch disk is 200mm, while the stock disk for a E16 B11 is 180mm, but both have the same part number for the flywheel, so we'll see if it works
transmission inpunt shaft spline count and width differs between E15ET and E16, so I'd say no.
by B11Chris
Wed Feb 13, 2019 5:11 pm
Forum: General Tech & Modifications
Topic: Clutch?
Replies: 6
Views: 4419

Clutch?

KiloooNL wrote: Sun Feb 10, 2019 5:21 pmAnd I run a standard exedy clutch (oem replacement clutch) and run 12psi all day long, no issues.
Thats what I just ordered. Research shows the stock E15ET clutch disk is 200mm, while the stock disk for a E16 B11 is 180mm, but both have the same part number for the flywheel, so we'll see if it works
by Wout-P11
Wed Oct 24, 2018 7:33 am
Forum: Members Rides & Introductions
Topic: Wout from the Netherlands
Replies: 9
Views: 5973

Wout from the Netherlands

... on intake, Weber 32/36 DGEV, Dbilas camshaft, header and a 2" exhaust. Before i fitted the rebuild RS5F30A-gearbox i fitted a lightened E13 flywheel. 1.jpg 2.jpg
by tassuperkart
Wed Jul 09, 2014 9:47 am
Forum: Members Rides & Introductions
Topic: Tassuperkarts GX Turbo (Updated again!)
Replies: 312
Views: 202172

... valve steps set against coolant temp. Pretty straightforward. Closed loop idle control is then specified. Even tho the cam is pretty big and the flywheel very light, the ECU controls idle speed very well with a nice and consistent idle around 1200 rpm. Thing is, just occasionally, the ecu drops ...
by tassuperkart
Sun Jun 01, 2014 2:14 pm
Forum: Members Rides & Introductions
Topic: n12 family
Replies: 60
Views: 40659

... up and glaze if really hit hard. Buttons dont like slipping at all. Shuddering and the buttons will machine their way into the pressure plate and flywheel faces remarkably quickly on a road car. But, will engage reasonably smoothly on really hard launching. Slip them at enough rpm and load and ...
by tassuperkart
Fri May 23, 2014 9:45 am
Forum: Members Rides & Introductions
Topic: 1983 exa turbo - bayside blue and 81POLR!!!!
Replies: 67
Views: 50875

... starter motor mounting holes to slide the starter a mm or 2 towards the engine. Check that the ringear is pressed hard back and evenly against the flywheel flange. If not your wasting your time with any workarounds. Secondly, check the sliding intermediate gear in the starter snout for excessive ...
by tassuperkart
Wed Apr 09, 2014 5:40 pm
Forum: Members Rides & Introductions
Topic: Tassuperkarts GX Turbo (Updated again!)
Replies: 312
Views: 202172

... grooves from the brass button clutch and it might take quite some time until the organic plate beds itself in fully. I should really have had the flywheel skimmed but the pressure plate was in need of a skim as well..... all getting too hard having to disassemble the pressure plate to remove some ...
by tassuperkart
Thu Mar 06, 2014 7:08 pm
Forum: Members Rides & Introductions
Topic: Tassuperkarts GX Turbo (Updated again!)
Replies: 312
Views: 202172

... now. Idle speed can vary quite a lot depending on various factors and the engine will sometimes race a bit and then chug away at too low revs. The flywheel is very light and cam is pretty tough. The engine runs very happily and reliably at 1150rpm idle but go much slower and it runs quite roughly ...
by leposima
Tue Mar 04, 2014 8:49 pm
Forum: General Tech & Modifications
Topic: ca18et swap transmission and clutch worries
Replies: 3
Views: 5412

Ok :) I'll have compared the ca18et flywheel and the cd17 flywheel and they seem to be have almost same diameter, and the ca18et seems to be bit lighter.. I notided P11 TD has 225mm clutch plate with same amount of splines as e15et clutch. ...
by leposima
Fri Feb 28, 2014 8:18 pm
Forum: General Tech & Modifications
Topic: ca18et swap transmission and clutch worries
Replies: 3
Views: 5412

ca18et swap transmission and clutch worries

... clutch hold that amount of torque. Now I have gearbox and (power train) from CD17 diesel engine, but I'm hesitating should I use gearbox (and flywheel) from CA18 instead, then I would need to install hydraulic clutch sylinders as well, but it would allow me to use Ca18det clutch, which can ...
by photoglossy
Tue Jan 21, 2014 4:02 am
Forum: Members Rides & Introductions
Topic: SR20VET P12 - Photoglossy
Replies: 33
Views: 28149

... http://i42.photobucket.com/albums/e329/photoglossy/start.jpg And this is how it looks about now. Motor going in. With newly made single mass flywheel replacing the dual mass unit, and new clutch. Also using the factory 6 speed manual box. http://i42.photobucket.com/albums/e329/photoglossy/motorin.jpg ...
by photoglossy
Mon Jan 13, 2014 10:40 am
Forum: Members Rides & Introductions
Topic: Mikes Exa - NZ
Replies: 371
Views: 149333

... http://i42.photobucket.com/albums/e329/photoglossy/motorout.jpg Turbo motor has gone in with a custom single mass flywheel replacing the worn dual mass unit. http://i42.photobucket.com/albums/e329/photoglossy/motorin.jpg http://i42.photobucket.com/albums/e329/photoglossy/flys.jpg