What HE said and same experience.
In my case the loose pulley was destroyed and the snout of the crank damaged.
Unbolt the starter so you can sprag the starter ring gear with a big fuckoff screwstick and tighten the bolt to spec.
Do it right the first time.
Oracle
N12Turbo.com lanyards are now available! Click here to visit the shop
Search found 54 matches: crank pulley
Searched query: crank pulley
- Fri Nov 29, 2013 7:32 pm
- Forum: General Tech & Modifications
- Topic: s-cargo removing flywheel pulley?
- Replies: 13
- Views: 5605
- Wed Nov 20, 2013 10:15 pm
- Forum: General Tech & Modifications
- Topic: s-cargo removing flywheel pulley?
- Replies: 13
- Views: 5605
s-cargo removing flywheel pulley?
... the belt and gubbins I realise that I now have to remove the flywheel pulley to get at the tensioner which is hidden behind a cover obscured by ... which is not the case for me. so how in the hell do you lock off the crank to allow you to undo the 19mm bolt that retains the flywheel pulley? ...
- Sat Feb 23, 2013 6:48 pm
- Forum: General Tech & Modifications
- Topic: fun times with timing belts and cam shafts
- Replies: 9
- Views: 5235
fun times with timing belts and cam shafts
... check spark plug holes to make sure valves not off. go to rotate the crank by hand and it moves smoothly a split second then jumps teeth on the belt so i go and check to the cam shaft pulley to find that it hasn't moved an inch. won't budge at all... shit repeated ...
- Thu Jan 24, 2013 5:36 pm
- Forum: General Tech & Modifications
- Topic: Oil Pump Jackshaft Gear Split, Help Please!
- Replies: 8
- Views: 3956
- Sun May 06, 2012 8:47 pm
- Forum: Members Rides & Introductions
- Topic: Tassuperkarts GX Turbo (Updated again!)
- Replies: 312
- Views: 212873
... engine/box out. Quite a bit of oil spray from a long time leaking front crank seal. https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/576442_3626747019887_1010375078_3328446_224872383_n.jpg ... discovered was a badly damaged Woodruff key which locates the lower cam pulley and the front pulley. ...
- Tue Dec 28, 2010 8:35 am
- Forum: General Tech & Modifications
- Topic: microtech questions?
- Replies: 10
- Views: 4022
... are different by a long shot in a CA to an E15 2: What was the initial cranking timing after locking the timing at (blah) degrees and winding over ... still set at 10 degrees and verify that 10 degrees shows on the crank pulley with a strobe. Just unlock the dissy and turn this way and that until ...
- Mon Sep 27, 2010 8:21 pm
- Forum: General Tech & Modifications
- Topic: A few questions
- Replies: 6
- Views: 1976
- Thu Jul 01, 2010 9:16 pm
- Forum: General Tech & Modifications
- Topic: rebuilding my E15ET
- Replies: 12
- Views: 4990
- Wed Jun 16, 2010 8:28 pm
- Forum: Article Submission
- Topic: How to correctly install a timing belt
- Replies: 0
- Views: 6978
How to correctly install a timing belt
... need a 10 mill socket and to lay under the car you will see a small pulley undo the bolt( some may need a little encouragement with the perswation ... the bottom has a smaller mark on the block and a small indent on the crank sprocket. Now i dont have an image of that but i have managed to get ...
- Mon Jun 14, 2010 3:52 am
- Forum: General Tech & Modifications
- Topic: Timing Belt Issue
- Replies: 6
- Views: 2181
- Mon May 17, 2010 8:57 pm
- Forum: General Tech & Modifications
- Topic: JDM pulsar n12 e15s engine swap
- Replies: 2
- Views: 2506
JDM pulsar n12 e15s engine swap
... doest run. I tried to turn engine with 19mm socket by applying it onto crankshaft pulley bolt. And it doesnt turning clockwise (turning it CCW i only unscrew it). Then i put ...
- Sat May 08, 2010 12:38 pm
- Forum: General Tech & Modifications
- Topic: Changing distributors
- Replies: 11
- Views: 4779
... setup is only funky and peculiar due to the very advanced nature of the crank position signal which is in the vicinity of 60 degress BTDC or nearabouts ... Magnetic Reluctor style sensors require magnets embedded into the pulley. They generate a totally different output which is usually a sine ...
- Sun Apr 18, 2010 10:34 am
- Forum: General Tech & Modifications
- Topic: Electronic timing (Dizzy)
- Replies: 35
- Views: 8851
- Sat Apr 17, 2010 12:43 pm
- Forum: General Tech & Modifications
- Topic: Electronic timing (Dizzy)
- Replies: 35
- Views: 8851
... atempts at pulling it a tooth back i put it smack bang on tdc at the crank and then pulled it a half a tooth forward on the cam witch in theory ... or you dont. Move half a tooth and the belt teeth are riding up on the pulley teeth and not meshed. FAIL. Now, a fundamental mistake for new players ...
- Thu Apr 15, 2010 7:11 pm
- Forum: General Tech & Modifications
- Topic: Electronic timing (Dizzy)
- Replies: 35
- Views: 8851
... see how we go The cam sprocket is advanced one tooth v's TDC. Set the crank sprocket to TDC, and wind back the cam 1 tooth. Assuming that you are ... mark is on, if its to the left skip the belt foward a tooth on the cam pulley, and vice versa. if the cam belt is excessivly worn/stretched you ...