N12Turbo.com lanyards are now available! Click here to visit the shop
Search found 97 matches: camshaft
Searched query: camshaft
- Wed Oct 24, 2018 7:33 am
- Forum: Members Rides & Introductions
- Topic: Wout from the Netherlands
- Replies: 9
- Views: 7793
Wout from the Netherlands
... a rebuild and upgraded E16S and rebuild gearbox in. Engine specs: Sunny B12 E16S fully rebuild, light porting on intake, Weber 32/36 DGEV, Dbilas camshaft, header and a 2" exhaust. Before i fitted the rebuild RS5F30A-gearbox i fitted a lightened E13 flywheel. 1.jpg 2.jpg
- Wed Feb 27, 2013 5:02 pm
- Forum: General Tech & Modifications
- Topic: fun times with timing belts and cam shafts
- Replies: 9
- Views: 5250
- Tue Feb 26, 2013 8:42 pm
- Forum: General Tech & Modifications
- Topic: fun times with timing belts and cam shafts
- Replies: 9
- Views: 5250
- Thu Feb 14, 2013 3:25 am
- Forum: Members Rides & Introductions
- Topic: Jan's N/A Pulsar [pix + vidz 2013-03-23]
- Replies: 428
- Views: 164278
... I have time to readjust the clearances): http://www.youtube.com/watch?v=k1dMYdJfhgY Compare to this video, where I'm still running on the old camshaft. The chuff-chuff sound was very pronounced at idle, and the engine was backfiring quite a bit while revving up the engine: http://www.youtube.com/watch?v=ca2huqwlbzM ...
- Wed Feb 13, 2013 9:41 am
- Forum: General Tech & Modifications
- Topic: Possible camshaft issues...
- Replies: 9
- Views: 4283
- Wed Feb 13, 2013 6:34 am
- Forum: Members Rides & Introductions
- Topic: Jan's N/A Pulsar [pix + vidz 2013-03-23]
- Replies: 428
- Views: 164278
- Wed Feb 13, 2013 6:26 am
- Forum: Members Rides & Introductions
- Topic: Jan's N/A Pulsar [pix + vidz 2013-03-23]
- Replies: 428
- Views: 164278
... the old head gasket finally blew as you know. I took some time to replace it and clean up the engine on the inside a bit at the same time. The camshaft seal behind the camshaft pulley was leaking and it had soaked the cam belt with engine oil. Had to replace the cam belt. Also did both a coolant ...
- Wed Feb 13, 2013 5:23 am
- Forum: General Tech & Modifications
- Topic: Possible camshaft issues...
- Replies: 9
- Views: 4283
... http://i213.photobucket.com/albums/cc119/TurboZBuzz/Engine/N12_2012-01-28_3110_zps181cff95.jpg Old camshaft: http://i213.photobucket.com/albums/cc119/TurboZBuzz/Engine/N12_2012-01-28_3104_zps33f0e334.jpg New camshaft: http://i213.photobucket.com/albums/cc119/TurboZBuzz/Engine/N12_2012-01-28_3105_zps651f0100.jpg ...
- Wed Jan 23, 2013 7:51 pm
- Forum: General Tech & Modifications
- Topic: Possible camshaft issues...
- Replies: 9
- Views: 4283
Possible camshaft issues...
... test before concluding it's the cam that's causing the chuff-chuff problem. May be piston rings just as well. If it turns out to be the camshaft, is there enough room in the engine bay to replace the camshaft (including rocker shaft and arms of course) without taking the head off? Thanks!
- Tue Nov 20, 2012 4:59 pm
- Forum: Members Rides & Introductions
- Topic: Tassuperkarts GX Turbo (Updated again!)
- Replies: 312
- Views: 217194
... 11.5 to 11.8 afr when dead cold to almost warmed up while holding a steady 1200rpm slowing to about 1050rpm when warm. The characteristics of this camshaft make idle speed below 1000rpm just too inconsistent even using closed loop idle speed control. I still have a small issue with the motor starting ...
- Tue Jun 19, 2012 11:27 pm
- Forum: General Tech & Modifications
- Topic: An article suggestion: cross-engine parts list!
- Replies: 17
- Views: 7073
... and external fan will exhaust manifold gasket intake manifold gasket headgasket BK440MT oil pan gasket rocker cover gasket front main/rear main/camshaft seals heater hoses engine mounts all the same with n/a and turbo Starters are not the same between NA and turbo! Exhaust manifold gasket is ...
- Tue Jun 19, 2012 9:37 pm
- Forum: General Tech & Modifications
- Topic: An article suggestion: cross-engine parts list!
- Replies: 17
- Views: 7073
- Sat Jul 23, 2011 8:39 pm
- Forum: General Tech & Modifications
- Topic: Need help with head
- Replies: 1
- Views: 967
Need help with head
... advice on head work, have got myself an e16 head, am planning to do the 1680cc conversion, and am wondering what is the best compression ratio and camshaft grind. Not looking for a "this is good" setup, but a "this is the best available" setup. Reason for asking, have been receiving ...
- Fri Jul 15, 2011 8:23 pm
- Forum: General Tech & Modifications
- Topic: Oversized valves
- Replies: 4
- Views: 1709
Oversized valves
Hey guys, Have now got myself a spare 15m head and a jap spec manifold, am planning on doing some work to it, valves, springs, camshaft etc. Am I able to get oversized valves for it?? And also is there anywhere that does lifters?? Price not really an issue lol, and if available, what ...
- Thu Jun 16, 2011 10:43 pm
- Forum: General Tech & Modifications
- Topic: how much power
- Replies: 15
- Views: 6446