Search found 84 matches

by congers87@hotmail.com
Mon Jun 03, 2013 10:01 am
Forum: General Tech & Modifications
Topic: Fuel pump current draw
Replies: 12
Views: 2951

Fuel pump current draw

And yes Tas I have tried 3 afms. They all create the same condition but the current one works the best up to 3000rpm
by congers87@hotmail.com
Sun Jun 02, 2013 9:31 pm
Forum: General Tech & Modifications
Topic: Fuel pump current draw
Replies: 12
Views: 2951

Fuel pump current draw

Thanks Tas. After my last post I came across your posts about the motherborad plugs. That sounds a goer. Did you only do this to the AFM wires? If I remove the standard plugs can I drill out their housing and slide the moterboard plugs through those holes? How did you do it? I'm just trying to pictu...
by congers87@hotmail.com
Sun Jun 02, 2013 7:59 pm
Forum: General Tech & Modifications
Topic: Fuel pump current draw
Replies: 12
Views: 2951

Fuel pump current draw

I found an old post and have tried Ben Hewitson's technique where he bends the pins slightly to create a better contact. No improvement. Any other ideas Tas? Did somebody once have sucess soldering indiviul wires on to the ecu pins?

Cheers
Chris
by congers87@hotmail.com
Sun Jun 02, 2013 4:33 pm
Forum: General Tech & Modifications
Topic: Fuel pump current draw
Replies: 12
Views: 2951

Fuel pump current draw

Doing a fuel pump current draw on a standard pump. I am reading 3.8 amps during priming. Is this healthy? UPDATE: The car idles perfect and revs fine up to 3000rpm but still wont rev beyond 3000rpm. I have checked and sorted the Water temp sensor, coil, leads, sparks, fuel pressure, wiggled the ecu ...
by congers87@hotmail.com
Wed Jan 23, 2013 4:15 pm
Forum: General Tech & Modifications
Topic: Idles Fine but Rich Misfiring revving
Replies: 3
Views: 1492

Idles Fine but Rich Misfiring revving

I had probed the temp sensor wiring at the ECU connector and across the terminals of the sensor which I repeated today. Approximating the sensor was probably around 20 degrees it hit the specified resistance from the manual (maybe a full heating test is necessary?). No change in running. I had check...
by congers87@hotmail.com
Tue Jan 22, 2013 2:16 pm
Forum: General Tech & Modifications
Topic: Idles Fine but Rich Misfiring revving
Replies: 3
Views: 1492

Idles Fine but Rich Misfiring revving

Hi guys, It has been a while since I've been here. The beastie is so close to complete after 2 and a bit years. Now comes the part of getting this thing to run as sweet as it did before. The car idles good. On start up around 1200rpm with an occasional burp. Fueling doesn't make your eyes water. Cur...
by congers87@hotmail.com
Thu Dec 22, 2011 9:50 am
Forum: General Tech & Modifications
Topic: Reinstalling Injectors
Replies: 2
Views: 616

Reinstalling Injectors

Cheers. I went that approach. I gave up trying to push the injectors into the seals while the seals were already in their housings. I just pushed the seals all the way down the pintle caps, located the pintle caps into the bores in the runners and tightened up evenly. Wolah, sealed up fine. Talk abo...
by congers87@hotmail.com
Wed Dec 21, 2011 10:24 am
Forum: General Tech & Modifications
Topic: Reinstalling Injectors
Replies: 2
Views: 616

Reinstalling Injectors

When reinstalling the stock injectors do I need to place the injector seals in their housings, in the runners and then install the injectors and tighten. Or do I place the injector seals around the pintle caps, align the injectors and install and then tighten it all up. I'm worried one way won't pro...
by congers87@hotmail.com
Thu Nov 24, 2011 9:32 pm
Forum: General Tech & Modifications
Topic: Exhaust manifold
Replies: 4
Views: 985

Exhaust manifold

If it's not straight but overall in good nick you can get it faced for under a $100. May save you if you buy a fucked secondhand number and end up with same problem.
by congers87@hotmail.com
Tue Oct 18, 2011 6:52 pm
Forum: Trader Rating (Private Sellers)
Topic: Dexi Styles
Replies: 10
Views: 11614

Dexi Styles

Once again great seller. Easy to contact. Happy to help and packs items well.

Cheers mate,
Chris
by congers87@hotmail.com
Wed Oct 12, 2011 9:17 am
Forum: Off Topic Discussion
Topic: youtube nutbags!
Replies: 3
Views: 1411

youtube nutbags!

Holy f'n shit....holy f'n shit....holy f'n shit.
by congers87@hotmail.com
Tue Sep 27, 2011 9:41 pm
Forum: Off Topic Discussion
Topic: Insurance
Replies: 15
Views: 2568

Insurance

Having previously worked in the car insurance industry, and having many friends who still do, in my opinion anyone who does not have at least third party property -i.e cover for damage your car may cause - is a fool. My ET is insured for $5k agreed value, classed as "highly modified" by the insurer...
by congers87@hotmail.com
Tue Sep 27, 2011 12:03 pm
Forum: Off Topic Discussion
Topic: Insurance
Replies: 15
Views: 2568

Insurance

I wonder if it's worth buying 3rd party insurance for our cars when we mod the turd out of them. At the end of the day when you look at the just car insurance product disclosure statement (my insurance) they will only cover me for legal modifications. So to me that 'unlimited modifications' claim th...
by congers87@hotmail.com
Tue Sep 27, 2011 9:28 am
Forum: Off Topic Discussion
Topic: EOI ARP head Stud Kits Group Buy
Replies: 30
Views: 6561

EOI ARP head Stud Kits Group Buy

Interested. Can you confirm the price before you need the deposit?

Cheers,
Chris
by congers87@hotmail.com
Tue Sep 20, 2011 9:43 am
Forum: General Tech & Modifications
Topic: Gearbox issues
Replies: 11
Views: 2205

Gearbox issues

People have claimed to chew through less boxes after merging the N13 gearset. I think I have heard banter on this forum about nissan using better metallurgy in the N13 box. Personally I couldn't tell you. Learn to use the search tool on here and I'm sure you can dig up some shit from past conversati...